Patreon Rewards – September 2021

 

Welcome to the Horrorscapes.

The theme of these models is generally - horror. While creating them, I was strongly inspired by the works of Giger and Beksiński.

They do not require the use of any supports, they can be freely scaled (although then the quality strongly depends on the capabilities of your machines). I tested them on both an FDM printer and a resin printer (significantly downscaling the models and printing them without supports, directly flat on the table, using a flexible magnetic plate).

I divided two models with extreme overhangs (heads) into two parts so that they could be printed without supports.

Separately printed heads should be glued to the rest of the body. I also added "full" versions of these models if you would like to try to print them in one part, using your own supports.

Models included in this set:

  • 4 elements of Horrorscapes Architecture
  • Horrorscapes Peculiarity Gate
  • Horrorscapes Peculiarity Wall
  • Peculiarities (Statues / Huge Characters) - 5 different versions
  • Horrorscapes cathedral facad - 4 pieces

Models from this set do not require any supports.

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

Patreon Rewards – August 2021

 

In this set you will find steampunk-inspired modular buildings (new and damaged versions), two types of gates, walls, a clock tower and devices such as a tesla-coil or a street lamp.

Models included in this set:

  • Modular Mansion (undamaged): First Floor, Middle Floor, Roof, Zero Floor (stairs).
  • Modular Mansion (damaged): First Floor, Middle Floor, Roof, Zero Floor (stairs).
  • 2 different Tesla Coils
  • 2 variants of a Gate
  • Wall
  • 2 variants of Generators
  • Lantern
  • Steampunk Generator Wall (Ring)
  • Steampunk Clock Tower

Models from this set do not require any supports.
The doors on the Mansion models are quite wide, but printers should have no problem printing them thanks to bridging. If you are not sure if your printer cooling can handle them, you can use the presupported versions that I have included in the set. Pre-built supports should be torn off after printing is finished.

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

Patreon Rewards – July 2021

 

Hope you are ready for the adventure, because this month I invite you on a journey to The Deepest Caverns!
All elements from this set do not require the use of any supports, are easy to print, and their diversity will allow you to build a great gaming table.

There are 57 files in this set, so the choice of models is quite big.

I divided the models from this set into three categories:

  • Caverns Mushrooms

You will find 11 models of "mushroom trunks" and 10 different mushroom caps. You can easily change the scale of the printed mushrooms, but remember to change the size of both the trunks and the cap.

  • Giant Mushroom Houses

Two kinds of giant mushrooms - big enough to hide in. Mushroom roofs print separately and are removable. In this folder you will also find versions of these mushrooms that are not empty inside (so, well ... they are just enormous mushrooms).

  • Caverns Elements

This category contains 29 different models - rocks, stalagmites, crystals and also rocks with mushroom trunks (print hats of your choice in a standard scale).

I hope you like this set!

It will suit any Underdark (or any other cave-related) adventure/gaming table!

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

Patreon Rewards – June 2021

 

In June Rewards, you will find mainly additions to the set from the previous month. But! You can create great ruins without even using any files from the previous month.

This time, however, there's more emphasis is on FDM printing (although many of the new models can also be easily printed on a resin printer).

List of models in June Rewards:

  • Gothic Tower / Bell Tower - modular, not requiring any supports. The bell is a separate element, printed upside down (so that it does not need supports).
  • Pre-defined ruins and their elements that do not require joining / sticking with other models - I created them for people who do not want to play with modular, multi-element models.
  • Additional elements for the modular set of gothic ruins.
  • I also added experimental elements to the May models, thanks to which you will be able to create multi-story ruins - I suggest using them only in FDM prints. I'm afraid resin models would be too heavy for such multi-story structures. Unfortunately, these elements require the use of supports. I thought for a long time how to create an elegant connector that would not require supports, but in this particular case it is probably impossible, unfortunately.

 

I hope you enjoy the models!

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

Patreon Rewards – May 2021

 

This is probably the most ambitious project I have ever created for my Patrons.

This month's bundle includes a modular gothic ruin kit. These models are designed so that they do not require the use of any supports - both in FDM printing and resin printing.

The set includes 22 elements - each of them was printed many times using an FDM printer (Artillery Genius) and a resin printer (Elegoo Mars Pro 2). After each test print, the parts were corrected and refined so that they use as little material as possible, are not time-consuming and have the best possible fit.

Important: For resin printing, I would strongly recommend using flexible magnetic buildplate. Thanks to it, the prints (especially the flat ones) will not be a problem when detaching from the buildplate.

 

You can connect individual wall segments with each other using 3mm x 1mm magnets or simply using glue / blu tack. The connecting pieces also have holes of 2.2mm in diameter, so you can use  2.2mm wires/strands for connecting these pieces.

The largest elements from this set have dimensions of 126.7mm x 15.53mm x 79.95mm - so they will be suitable even for small popular printers (diagonally) - in the case of slightly larger printers such as the Mars Pro 2 on which I tested these models, you will even be able to print 4 main walls simultaneously.

If you have both types of printers, there is nothing to prevent you from connecting the elements printed with filament and resin, then you decide what quality you expect from a given element of the set.

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

 

Patreon Rewards – April 2021

In the April pack you will find a new version of my very first model dedicated to 3D printing - The Vined Throne. The new version is much more complex and rich in details (it is best to print it using low layer heights), I spent a lot of time to make sure that it can be printed without any supports. This model is a reference to my other models such as the Goddess of Life etc.

I hope that this model will not offend anyone - I wanted to refer to classic sculptures and paintings showing beauty (in this case - quite intimidating and disturbind beauty) - without a doubt I do not treat it as a study of oversexualized pin-ups, which I do not like.

I am also attaching a few bigger vines to the throne that will look good in his company.

The second part of this set is The Place of Knowledge. It consists of a huge statue of the mysterious Lore Seeker - his hand has a flat platform on which any human-like miniature can fit. The head is available in three versions - full/complete, hollow inside with a hole (the walls are about 4mm thick) and ruined, which can serve as a temporary shelter from enemy arrows or bad atospheric conditions.

The last element of these Rewards are Ritual Circles in two variants. One is "classic", the other one refers to the throne and larger vines, so they can be used in a set.

I hope you will like these models.

Models included in this set:

  • 2 variants of Ritual Circle
  • Small Jungle Tendrils
  • Throne of Vines (2021 version)
  • The Place of Knowledge set (3 pieces)

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • 2 variants of Ritual Circle
  • Small Jungle Tendrils set
  • Throne of Vines (2021 version)
  • The Place of Knowledge set

Patreon Rewards – March 2021

For this month I would like to present you The Bone Stronghold plus a small bonus - the Bone Monolith and Bone Pillar models.
Thanks to this bundle you can create an impressive Stronghold mean for any death-related army/nation/ruler. It's heavily inspired by Ossiarch Bonereapers faction by Games Workshop.

Models included in this set:

  • 4 variants of walls
  • wall corners
  • gate + "skull gate topper", printed separately
  • 2 variants of wall floors
  • stairs
  • The Bone Monolith
  • The Bone Pillar

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Bone Monolith + Pillar
  • Bone Stronghold

Patreon Rewards – February 2021

In this set you will find quite unique, inspired by Indonesian architecture pieces of scenery.

Working on them was a great pleasure, so I would love to expand this set at some point in the future.

Models included in this set:

  • The main temple
  • Three Ritual Platforms
  • Ancient gate
  • Ancient lookout
  • Walls
  • Two reptile statues
  • Shrine
  • Two separate columns

I hope you will like this set, it's a bit... different, so I reallyhope you will find it interesting.
It should be useful for RPG scenery and also wargames (especially for jungle themed gaming boards).

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Baronghan Shrine - Temple Complex

Patreon Rewards – January 2021

Welcome to the Sunken City!
This adventure will lead us to the corners of the underwater ruins of an ancient city - or on the contrary - perhaps it is a city that has been hidden under the water for hundreds of years, and only recently appeared on the surface ...? It will be up to you.

This set includes many barnacles covered objects, as well as elements that you can use to spice up the storyline of your adventure or to diversify your battlefield.

There are many ruins, architectural elements, a throne room, strange-looking geometric structures, and even a giant crab patiently waiting for its victims await in this bundle.

Models included in this set:

  • Sunken City Columns (2 versions)
  • Sunken City Huge Crab
  • Sunken City Ruins #1 - #5
  • Sunken City Throne
  • Sunken City Wall
  • Sunken Scatter Island 1# - #3

and also - Embowed Set:

  • 4 Arcs with optional connectors. These structures are printable in 2-3 pieces.
  • Embowed Scatter Ruins (5 versions)

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Sunken City Set

Patreon Rewards – December 2020

I am pleased to present you the December Rewards - The Floating Islands Set.
When designing this set, I wanted it to be an interesting product also for people who are not interested in using actual flying islands. Thanks to this, you will find a variety of scatter scenery that I used to create the islands - all elements such as obelisks and crystals can be printed separately and used in any way not related to flying islands.

There are nine islands - they are divided into small and large. They all stand on rods that can be printed or purchased (for example, on Amazon. Unfortunately, acrylic clear rods don't come really cheap). Large islands use 1 inch rods, small islands use 0.5 inch rods. The minimum height of the rods that can be used for this design is 15cm.

In the files you will find printable rods with a height of 15cm, 20cm and 25cm

All the islands are printed in two parts and can optionally use magnets. The maximum size of the magnets that can be used for the islands is 15mm (diameter) x 3mm (height). If you are using lower magnets, I suggest you use some kind of putty or thick glue to fill the slot.

The upper parts of the islands have been designed to be an interesting element of the scenery even when lying flat on the table. In this way you can get interesting hills with columns or crystal formations, for example.
The set also includes separate lower parts of the islands without any holes - they can be used as hills and rock formations.

Two variants of bases for the islands are also included. Thanks to them, the islands should stand firmly on the table. I suggest using a slightly larger infill for them to make them heavy enough, or weight them down in some other way.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

 

List of files:

  • Floating Islands Set

Patreon Rewards – November 2020

Welcome to the catacombs! Models from this month are heavily inspired by Skyrim, Diablo and new GW's product - Warcry: Catacombs. I created models suited for interiors and exteriors - braziers, gates, sarcophagi, small bridge etc.

Models included in this set:

Catacombs Burial Niches + Corpses
This set is modular and allows for various configurations (check the pictures for reference)

Dungeon Gates
2 tops and 2 bottoms that are interchangeable. No need for any supports

Dungeon Braziers
2 versions with the possibility of printing a lit or extinguished torch

Catacomb Sarcophahus
A comfortable resting place for all the dead (and undead). In various configurations, so you can use these models in different ways

Dungeon Wells
Standard version + version with some skulls

Models from this set do not require any supports (if you are using an FDM printer).

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Catacombs Burial Niches
  • Catacombs Corpses
  • Dungeon Gates
  • Dungeon Braziers
  • Catacombs Sarcophagus
  • Dungeon Wells
  • Dungeon Skull Bridge

Patreon Rewards – October 2020

For this bundle I have for you two sets of scenery: The Boneyard of Titans and the Arcane Cogs set. I created the first one with the upcoming (lte me remind, the set was published in October) in mind, you may want to use it for a spooky RPG session or a Warhammer death (or simply Giant) themed battles.

Models included in this set:

The Boneyard of Titans
This set consists of: 4 elements of a huge chest, a shattered skull and a skull turned into a shrine, "decorated" with human skulls and runes.

Arcane Cogs
The second set includes 11 Arcane Cogs - they can serve as mysterious structures, the architecture of a long forgotten magical race, or perhaps as a product of the filthy Xenos. Initially, I wanted to put runes on them, but a few people suggested that without runes they would be more universal and fit even science fiction settings.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presen

List of files:

  • Arcane Cogs
  • The Boneyard of Titans

Patreon Rewards – September 2020

For this set I have prepared models for you that are related to lava, fire, skulls and generally not very friendly locations.

The rocks that are included in this pack are quite universal, so you can use them in any RPG adventure or on any wargaming table.

Models included in this set:

Lava pools (3 variants)
An element of the landscape that will be useful in any volcanic location, hell or areas inhabited by demons.

Rock Islands - 5 variants + 2 variants with skulls
A universal piece of scenery that will find its place on every gaming table. Much depends on how it is painted - it can serve as a traditional "hill" if you use static grass, it can also be a rock mass in caves, etc.

Arcane Location - Fire
What types of rituals may be performed on a runic platform surrounded by lava? The most interesting ones. This huge piece of scenery will look great on any table. Don't forget to check out the color guide for this model.

Maw of Fire
This piece of scenery will suit any Hell / Volcano / Plane of Fire / Chaos themed table for your RPG adventures and wargaming battles. Check out the color reference for this piece.

Rock of Skulls
This small rock, decorated with numerous skulls, undoubtedly tells a lot about the inhabitants of its neighborhood. Easy and quick to print model that fits any gaming table.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Arcane Location - Fire
  • Lava Pools
  • Maw of Fire
  • Rock Islands
  • Rock of Skulls

Patreon Rewards – August 2020

This set is different from the previous few. Nature's themes have been replaced with steel, wires and cold mechanisms. In addition to elements with sci-fi / steampunk / eberron themes, there are elven shrines in five versions.

Models included in this set:

Modular Mechatower
This set is just perfect for any Skirmish-type game. It's highly customizable and very easy to print. It does not require any supports. Printing some kind of complex board filled with these towers will be quite time-consuming, yes, but it will be very rewarding.
There are 10 files in this set: 2 bases, 3 variants of mid-sections, 2 tops - you can mix them as you want, and then connect them with bridges. Want just a single tower? Fill the empty spaces in floors using "Floor Short Extensions".
The way of connecting these pieces is super simple, or even primitive - but it's a good thing in my opinion. You don't need to print additional "locks" or "connectors".
Clean, easy, elegant. Personally, I will use my towers for Kill Team and small games of Warhammer 40k.

Corporation's Monument
Well, it's a little bit odd piece. It's clearly inspired by classic Sci-fi movies (like Blade Runner) and it's more... "artsy" than most of scenery pieces that I created.
This model is actually quite easy to print. You will need to use a little bit more infill than normally (for my test print I used 15% of Cubic infill), I also would suggest using lower than 0.2mm layer height for the best results.
The first version of this piece was a little bit more complex, but it needed supports, so I decided to simplify it. I tested the final version twice - without any supports.

Shrine of Light - Set
This set includes 5 variants of a Shrine of Light (but there are 2 main "templates"). I wanted to create something interesting with the new GW's Lumineth Realm-Lords in mind.
These pieces look similar to the Hysh shrines from WFB world, but they're decorated with gems and other symbol.
You can use them as any other piece of terrain - elven or not. More neutral looking variants will suit even Sci-fi tables in my opinion.
Test printed without any supports. Make sure that your retraction settings are fine - you will retract quite a lot printing these models.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.
The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Modular Mechatower
  • Corporation's Monument
  • Shrine of Light Pack

Patreon Rewards – July 2020

When creating this tree pack, my goal was to create the most diverse set of supportless 3D printable trees (or rather a modular tree system). Flora in general is not the most exciting or most spectacular project to design, but (in my opinion) there was a shortage of interesting printable trees on the market that would not look artificially, like a toy, or resemble broccoli. I wanted to create a kit that was customizable, easy to print, and looked good on the table.

In the bundle you will find quite a lot elements:

23 tree variants, 13 branch variants, including 2 types of branches that allow you to create a weeping willow, as well as 2 variants of "cut" branches, which I created for people who are not fans of empty holes in tree trunks.

The system is based on "ball joints", which allow for great freedom in glueing and positioning elements.

In the initial version of the package (because I have plans of updating it at some point in future), you have the option of creating trees without any leaves (with leafless branches), weeping willows and deciduous trees thanks to the leafy "hats", which are also fastened with Ball Joints.

All three variants can be created using any of the 23 tree variants (except perhaps only one model, which is supposed to be a completely dead tree and has no holes).

Important note: the glue you use to glue the elements together must be strong enough. Personally, I use a thick superglue or superglue gel.

The package also includes some extras in the form of Bushes in three sizes, Active Arboreal Gate and The Treefolk Watchtower.

How to make a Weeping Willow:

1. Print a tree of your choice and some Branches, including Willow Branches. Make sure to use "Outer Before Inner Walls (shell section)" for printing Willow Branches (it will be much easier to print leaves with this option enabled).

2. Glue Branches to the tree (or paint it first, if you prefer. Painting a "stylized" willow branches is quite challenging).

3. Use a hairdryer or a heatgun to "stylize" the leaves, just like in case of the famous Hairy Lion (https://www.youtube.com/watch?v=OTXPU2P-ElE). Heat the leaves slowly, try to not overheat it.

Tips and How-To:

I strongly suggest you to use brims on these prints, especially if you're not sure about the adhesion on your tables.

Using Z-Hop, especially on Branches, is also not a bad idea.

Willow leaves print best when "Outer Before Inner Walls (shell section)" is used. This allows the leaves to print in a more orderly fashion.

I used 0.16mm layer height for all my test prints, I would say that is enough for the details. 0.12mm look better, but printing time is also quite longer.

Use the hair dryer carefully. Too much hot air can melt the leaves (or even other parts of the tree). A very hot filament can also burn the skin. It is better to spend more time styling the leaves than to expose yourself to negative results.


Models from this set do not require any supports (if you are using an FDM printer).


NOTE: 
This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Customizable Trees - 23 variants
  • Branches of trees - 6 variants
  • Branches - Cut - 2 variants
  • Willow branches - 2 variants
  • Bushes - 3 variants
  • Branches with a ball joint - 3 variants
  • Tree tops (foliage) - 2 variants
  • Arboreal Gate - Active
  • Treefolk Watchtower

Patreon Rewards – June 2020

This set will allow you to create, for example: a forest elf village/camp, a druid grove, or an urban district dedicated to nature (and the goddess of life) - and many more. It all depends on your imagination.

It contains models that are probably my favorite models that I have made so far.

Models included in this set:

Goddess of Life (including 3 ways of printing this piece)

One of my favorite models so far. I prepared it in three versions, which in general are the same, but they print in three different ways.

Version #1 of this model is appropriately divided into two separate parts. As a result, this model can be printed without using any supports - it has been tested by me and it works really good.
Both parts should be glued together after printing, I suggest using a superglue.

Version #2
of this piece is prepared for people who do not mind using a minimum number of supports. They are only required under the goddess's head (printed separately from the rest of the body).

Version #3 of this statue is dedicated to people who want to use their own supports (e.g. tree-supports), as well as those who would like to print this model using a resin printer.

This version is not cut in any way.

Leaf Pavilion #1, Leaf Pavilion #2, Leaf Tent, Leaf Tower #1, Leaf Tower #2, Lifepod #1, Lifepod #2
These models make up the "Leaf Village". It can be, for example, a small village inhabited by druids, or part of a larger agglomeration created by forest elves. These models were heavily inspired by classic cRPGs.

Tranquility Shrine 

Another model that belongs to the group of my favorites. It can serve you in many ways, but I sculpted it with a clear intention: I wanted to present the goddess of life and nature in a disturbing and non-obvious way. Tree branches grow out of her body, forming a wing-like shape around her. Her "wood" horns are also not an obvious element and unambiguously associated with the innocent or good aspect of the goddess of life.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Goddess of Life
  • Tranquility Shrine
  • Leaf Village

Patreon Rewards – May 2020

This whole set is dedicated to my favorite theme and the first set of scenery I created - The Tangled Realm. There you will find overgrown, massive vines growing out of the ground, tangled cliffs and a mysterious, ancient statue of a long-forgotten goddess.

Models included in this set:

Vined Cliffs
10 different vined rock formations. This kind of terrain shows up in many video games, so it may seem familiar to you. With these models, you can create well known cRPG locations to your gaming tables.

The vined passage
This type of gate, formed in (un) natural (some druids probably had their hands in it!) will be an interesting obstacle for many adventurers - or for entire enemy units on the battlefield.

6 different enormous jungle tendrils & 6 different small jungle tendrils
There is no doubt a story behind the rise of such enormous vines. What kind of story? It's up to you. If you are not interested in printing such large vines, you can easily scale them down in your slicer - they will still print well and without using supports.

Statue of the fallen goddess
Detailed, eye-catching, and awesome - but still easy to print. This statue can be the center-piece of your gaming table, especially if you paint it.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Statue of the Fallen Goddess
  • The Vined Passage
  • Vined Rocks
  • Jungle Tendrils (huge)
  • Small Jungle Tendrils

Patreon Rewards – April 2020

If you are looking for universal, modular, interesting, but at the same time easy to print pieces of scenery - this set will be perfect for you.

A large number of elements available to choose from will make your constructions perfectly tailored to your needs.

Models included in this set:

Modular Tower #1 (3 different floors, stackable)
This tower consists of three basic components that are easy to print and stackable.

Elven Tower (3 different floors, stackable)
A little bit more fancy version of the Tower. Elements from this set are fully compatible with the Modular Tower #1 above. You can mix them however you like.

Lion Tower Set
A set of simple towers decorated with the image of lions. These towers are much smaller than the rest of the towers in this bundle.

Elven Smaller Construction (3 versions) & Elven Obelisk (2 versions)
Additional elements to decorate your gaming table. These models, despite their complexity, do not require the use of supports. Make sure your retraction settings are correct before printing them.

Tower Footbridges - two versions
Two versions of ormamental foorbridges for connecting your Towers.


Models from this set do not require any supports (if you are using an FDM printer).


NOTE: 
This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Modular Tower #1
  • Lion Tower Set
  • Elven Obelisk
  • Elven Tower #1
  • Elven Smaller Construction
  • Tower Footbridges

Patreon Rewards – March 2020

Another great set strongly referring to nature, except for the dwarven landing pad and the mysterious Wailing Crystal. It will be extremely useful in building a scenery rich in various rocks (especially underground ones).

Models included in this set:

Wailing Crystal
This piece of scenery is very easy to print and it actually looks super good on the table. I suggest you to use smaller layer height for extra details. I printed it using 0.16 and 0.12 with great results.

Treefolk Watchtower
This is probably the biggest single piece of scenery I ever made. It's truly massive. It's not hollow - I ran some tests and hollowed version actually was printed A LOT longer (because of extra perimeters of the hollowed spaces). I suggest you to print it faster than usual, using 70-90mm/s speeds and 0.16 - 0.2 layer height. I test printed it using 8% Gyroind infill with 4 bottom and 7 top layers.

Gate of The Evergreen City
The model is great not only for tables with a forest-city theme, but also for display boards for your army - for example Living City army from Age of Sigmar.

Stalagmites - Cave Set #1
Simple, but effective set that will suit every goblin-inhabited cave.

Basalt Rocks Set #1
Sweet looking set of geometrical shaped rocks with some twist. Check out the cool Basalt Throne and the Spire.

Gyrocopter Landing Pad
This piece is very different from the rest of the set. It is not related to nature, on the contrary - complex mechanisms created by dwarven engineers make this landing site ready for the landing of aircraft of any size.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Basalt Set #1
  • Gate of the Evergreen City
  • Gyrocopter Landing Pad
  • Stalagmites Cave Set #1
  • Treefolk Watchtower
  • Wailing Crystal

Patreon Rewards – February 2020

The models from this set will help you build an interesting gaming board related to nature - and more. A temple hidden deep in the forest, or a city connected with nature - these are only the most obvious ideas on how to use these models.

Noteworthy models from this pack are also statues of captives, which can be used as "decoration" of more brutal places such as the battle arena or the palace of the reigning tyrant.

Models included in this set:

Captīvī Statue #1 &Captīvī Statue #2
These models are printed in several parts, so they are easy to print and do not require the use of supports. They will look exceptionally good when used with a stone-like filament.

Stylized Wolf Statues (set of 3 variants)
A simple, stylized statue of a wolf in three variants: "clean", covered with runes and decorated with primitive ornaments. This simple and quick to print a model that enhances each table. It looks great in any size.

Statue of The Cursed Ones
This monumental model features a werewolf statue covered in mysterious ornaments. The werewolf is presented in a rather neutral way, so it's up to you to decide on the narrative of this model: by whom was it created? By bloodthirsty, hostile lycanthropes, or perhaps peaceful moon worshipers?

Ancient Rotunda (2 versions)
These simple, universal models fit into any theme of your gaming table. The "clean" version has space for any statue or any other element.

Priestess Statue
This simple or even austere and blocky sculpture was created to represent a High Priestess in one of the human cities, but you can use it in many other ways.

Mother Tree
Strange and disturbing - this is the easiest way to describe this sculpture. What is its purpose? Does it protect the forest folk living in its vicinity, or maybe warn careless wanderers against imminent doom? It will only be up to you.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Captīvī Statue #1
  • Captīvī Statue #2
  • Stylized Wolf Statues
  • Statue of The Cursed Ones
  • Ancient Rotunda
  • Priestess Statue
  • Mother Tree

Patreon Rewards – January 2020

Models included in this set:

Anvil of Calamity
Cool dwarven-themed piece of scenery (you actually can use it as a miniature), printable 100% supportless in 4 parts. I added an ancient stairs to this set that will help your dwarves gain access to the anvil.

Dragon's Archway
Fairly big, but great looking scenery. Dragon theme will suit most gaming tables.

Dragon's Totem
The head of a giant dragon tied to a rune-covered rock. Does that sound good? Definitely. The narrative possibilities of this model are endless, it all depends on your imagination.

Death Shrine
Nice addon to other death-related pieces. You want to explore some kind of Death Realm or perhaps you are preparing Death Cult? Your Death Army needs more pieces of sceney? This model will help you get great results. Note, it's quite tall, double check it it's the size suited for you. It will print fine in any scale.

Everchanging Gate
Looking a way to the Chaos Realm? Or to the lair of Lords of Change? This gate will help you get there. Also, disturbing tentacles and eyes will be always look good on the gaming table.

Demon Gate
Big badass looking gate in two flavors. Don't like the symbol on top? I prepared the second version without any symbols. It will be much more universal this way.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Anvil of Calamity
  • Dragon's Archway
  • Dragon's Totem
  • Death Shrine
  • Everchanging Gate
  • Demon Gate

Patreon Rewards – December 2019

This set includes a lot of nice ruins and few death-related pieces of scenery. It will be great for any death-thematic or any other skirmish game tables.

 

Models included in this set:

Raven Throne
Ever wanted to print a huge throne made of giant raven's bones? Probably yes, although you didn't know that. Now's your chance. It prints fairly easily and without supports, but I suggest not saving on fan cooling.

Bone Monolith - In 2 versions. One has small skulls that may not appeal to everyone.
By default, these monoliths are about 12 cm high, but they will look great in any size. If you would like to print this element in 200% - it will look monumental and phenomenal, although it will definitely be a long print.

This monolith also looks great in a very small size, especially printed in resin - it can then be used e.g. as a Lich's  Phylactery or some death-related artifact.

It can also be used as a marker/ token/ objective for Death-related armies/heroes.

Bone Pillar
Just because more bones are always welcome. Fast and fun supportless print!

Lion Ruins Set
There's a lot of stuff in this set. 8 different pieces (+ one pre-mirrored) of ruins. Plus vine-less version of the Ruins Gate, previously available in November Rewards (just because it really belongs to this set).

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

 

List of files:

  • Bone Monolith
  • Bone Pillar
  • Lion Ruins Walls
  • Lion Ruins with Vines
  • Raven Throne
  • Ruins - Enter

Patreon Rewards – November 2019

Looking for universal scenery for your skirmish game? Or perhaps you're preparing scenery that will suit your future boss battle in D&D? This set will be a great choice.

Models included in this set:

Throne Room Set - including a throne, pillars (2 versions) and throne platform.

You can use these models with older Rewards and Ruins Entry for best results.  The Throne Platform is printed separately, so it can be used in many other ways.

2 Stylized Lion Shrines / Statues
Scale these models according to your needs.  They look really good on the default scale, but they can be scaled down (or up, if you like to go BIG).

Stylized Lion Throne
It will look especially good if printed using fine settings (0.12mm layer height etc).
I would suggest to spare some extra time for printing this piece.
It will not look super good on 0.2mm settings.

Ruins Entry - 2 versions( Clean and Overgrown)
Each version is printable in 4 parts. More ruins in this style will be added in the December Rewards.

The Forest Portal - Active Version

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Throne Room Set
  • 2 Stylized Lion Shrines / Statues
  • Stylized Lion Throne
  • Ruins Entry - 2 versions( Clean and Overgrown)
  • The Forest Portal - Active Version

 

Patreon Rewards – October 2019

This set, like the set from previous month, is very modular and gives great possibilities for configurability.

It is also fully compatible with the previous set, so you have even more options when creating your own scenery.
Some components have holes for optional 5x1mm magnets.

Models included in this set:

The base with stairs (Temple Stairs + Temple Floors with Insets)
It's the main element of this set. Overall, there are two styles of the Base in this set: "Clean" one and "Ornamental" one.  Floors are printable as one piece or in parts. They have a round inset printed separately. It will mask the connection line between halves of the floor. Also - I will make some other insets in future, so you will be able to swap them easily.

Columns and filars
Quite a lot of them - 8 different designs. You will be able to truly personalize your temple/ruins. You can also use them with other scenery. They are printable in two versions - stardard and with a hole for magnet.

Cat and Sphinx Bundle
This mini-set includes:
- A huge and worn female bust
- Big Sphinx
- Small Sphinx with base
-  2 types of Lioness Statue in 2 versions - based and baseless

Dais/Piedelstals
2 versions of 2 types of piedestals - Based versions of Cats will fit these perfectly.

Ramp for the Temple Stairs

Platforms/Ritual Platforms
4 versions of Platforms - 2 round and 2 square.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • The base with stairs (Temple Stairs + Temple Floors with Insets)
  • Columns and filars
  • Cat and Sphinx Bundle
  • Dais/Piedelstals

 

Patreon Rewards – September 2019

Any fan of desert kingdoms, monumental temples and the undead will love this set.
The models in this set are very modular, they can be used to create many very interesting configurations. The appearance of the final buildings depends on you, your imagination and on how many elements you will want to print.

Most models also have optional 5mm x 1mm holes for magnets. If you are not interested in using magnets, you can simply glue models together or use, for example, Blu-Tack.

The base with stairs (Temple Stairs + Temple Floor)
It's the main element of this set. It's printable in 5-6 parts (4 corners + floor. The floor can be printed in two parts). Please double check if your printing bed is leveled - it's super important to successfully print these parts.

Stair extenders
These elements are printable supportless up-side down (They're already in correct orientation, you don't have to change anything). These are structures adjacent to the stairs on which you can place columns or any other objects. Available in two flavors - neutral one, and Egyptian-like one wth hieroglyphs. Both versions are available with a magnet hole and without the hole.

Connector - Bridge
Similar to the Stair extenders, but printable in 3+ parts (you decide how long your bringe will be) or in one part (fixed length). You can use them to connect two main platforms.

Obelisks/Columns
A lot of variants - because a temple with 20 identical-looking obelisks does not look good.

3 variants of small generic obelisks
3 variants of small obelisks with skulls
2 variants of medium obelisks
1 huge obelisk with hieroglyphs
1 diamond-shaped monument

The Lioness Statue
2 variants: the first one do require using supports under the head, the second one does not require supports and the head is printed separately.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Temple - Main Body
  • Columns
  • Connectors
  • Lioness Statue

Patreon Rewards – August 2019

This set is heavily related to the previous Rewards, but it can be used without them.
It includes:

The Stone Hand Throne - printable  in 6 pieces or in 1 piece at your risk -  you will have to use a really  decent cooling if you want to print it  this way
The Mine Entry - printable in 2 parts without any supports
Wizardly Cave Entry
Wooden Scaffolding Towers - 3 sizes. No supports needed
Scaffolding towers tops - 2 square versions + 2 bridges
Scatter Rocks - 5 versions
Scatter Runed Rocks - 2 versions
Single Small Stone Pillars/Cliffs - 4 versions
1 Scaffolding  Extender - previously available also in June Rewards (2019)
Ladders - 2 versions; previously available also in June Rewards (2019)

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • The Stone Hand Throne
  • The Mine Entry
  • Wizardly Cave Entry
  • Wooden Scaffolding Towers
  • Scaffolding towers tops
  • Scatter Rocks
  • Scatter Runed Rocks
  • Single Small Stone Pillars/Cliffs
  • 1 Scaffolding  Extender
  • Ladders

Patreon Rewards – July 2019

Looking for an epic, modular cliff set perfect for your RPGs and skirmish games? Look no further!

This set includes Modular Stone Pillars that are heavily inspired by China's Zhangjiajie National Forest Park.
3 Pillars - Small (2 floors), Medium (3 floors) and Huge (5 floors). You can freely mix mid-floors from this set.
You will be able to use these models for many applications. A lot depends on how you will paint them. Use red-orange tones for desert hills, cold grey tones and snow for rocks in high mountains etc.

You will find a lot of inspiration under the following link: https://www.patreon.com/posts/july-rewards-28094212

It also includes Scaffolding Extenders (5 variants) - Just in case if default scaffolding is too small for your taste/needs. Just glue/bluetack them on top of the floor. The set also includes ladders - you will find two variants in it.
Wooden Footbridges will also be useful (two variants are included in this bundle) - Use them to connect your Pillars and Islands. As well as Plank Walls (7 variants included in this set) and Single Rock Islands - Those will be quite useful for connecting Pillars.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Modular Stone Pillars
  • Scaffolding Extenders
  • Ladders
  • Wooden Footbridges
  • Plank Walls
  • Single Rock Islands

 

 

Patreon Rewards – June 2019

This set includes models that will look great on any table - both fantasy and sci-fi themed. The generic (and universal) portals contrast with the mysterious and unusual looking Forest Lady Portals and Stone Prisons.
All of these models (except the Arched Portal) are printed in one piece. Neither model requires the use of any supports (using FDM printers).

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Arched Portal
  • Forest Lady Portal #1
  • Forest Lady Portal #2
  • Gate of Stars
  • Stone Prison #1
  • Stone Prison #2
  • Stone Tablet
  • Vined Wall