Patreon Rewards – September 2021

 

Welcome to the Horrorscapes.

The theme of these models is generally - horror. While creating them, I was strongly inspired by the works of Giger and Beksiński.

They do not require the use of any supports, they can be freely scaled (although then the quality strongly depends on the capabilities of your machines). I tested them on both an FDM printer and a resin printer (significantly downscaling the models and printing them without supports, directly flat on the table, using a flexible magnetic plate).

I divided two models with extreme overhangs (heads) into two parts so that they could be printed without supports.

Separately printed heads should be glued to the rest of the body. I also added "full" versions of these models if you would like to try to print them in one part, using your own supports.

Models included in this set:

  • 4 elements of Horrorscapes Architecture
  • Horrorscapes Peculiarity Gate
  • Horrorscapes Peculiarity Wall
  • Peculiarities (Statues / Huge Characters) - 5 different versions
  • Horrorscapes cathedral facad - 4 pieces

Models from this set do not require any supports.

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

Patreon Rewards – August 2021

 

In this set you will find steampunk-inspired modular buildings (new and damaged versions), two types of gates, walls, a clock tower and devices such as a tesla-coil or a street lamp.

Models included in this set:

  • Modular Mansion (undamaged): First Floor, Middle Floor, Roof, Zero Floor (stairs).
  • Modular Mansion (damaged): First Floor, Middle Floor, Roof, Zero Floor (stairs).
  • 2 different Tesla Coils
  • 2 variants of a Gate
  • Wall
  • 2 variants of Generators
  • Lantern
  • Steampunk Generator Wall (Ring)
  • Steampunk Clock Tower

Models from this set do not require any supports.
The doors on the Mansion models are quite wide, but printers should have no problem printing them thanks to bridging. If you are not sure if your printer cooling can handle them, you can use the presupported versions that I have included in the set. Pre-built supports should be torn off after printing is finished.

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

Patreon Rewards – July 2021

 

Hope you are ready for the adventure, because this month I invite you on a journey to The Deepest Caverns!
All elements from this set do not require the use of any supports, are easy to print, and their diversity will allow you to build a great gaming table.

There are 57 files in this set, so the choice of models is quite big.

I divided the models from this set into three categories:

  • Caverns Mushrooms

You will find 11 models of "mushroom trunks" and 10 different mushroom caps. You can easily change the scale of the printed mushrooms, but remember to change the size of both the trunks and the cap.

  • Giant Mushroom Houses

Two kinds of giant mushrooms - big enough to hide in. Mushroom roofs print separately and are removable. In this folder you will also find versions of these mushrooms that are not empty inside (so, well ... they are just enormous mushrooms).

  • Caverns Elements

This category contains 29 different models - rocks, stalagmites, crystals and also rocks with mushroom trunks (print hats of your choice in a standard scale).

I hope you like this set!

It will suit any Underdark (or any other cave-related) adventure/gaming table!

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

Patreon Rewards – June 2021

 

In June Rewards, you will find mainly additions to the set from the previous month. But! You can create great ruins without even using any files from the previous month.

This time, however, there's more emphasis is on FDM printing (although many of the new models can also be easily printed on a resin printer).

List of models in June Rewards:

  • Gothic Tower / Bell Tower - modular, not requiring any supports. The bell is a separate element, printed upside down (so that it does not need supports).
  • Pre-defined ruins and their elements that do not require joining / sticking with other models - I created them for people who do not want to play with modular, multi-element models.
  • Additional elements for the modular set of gothic ruins.
  • I also added experimental elements to the May models, thanks to which you will be able to create multi-story ruins - I suggest using them only in FDM prints. I'm afraid resin models would be too heavy for such multi-story structures. Unfortunately, these elements require the use of supports. I thought for a long time how to create an elegant connector that would not require supports, but in this particular case it is probably impossible, unfortunately.

 

I hope you enjoy the models!

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

Patreon Rewards – May 2021

 

This is probably the most ambitious project I have ever created for my Patrons.

This month's bundle includes a modular gothic ruin kit. These models are designed so that they do not require the use of any supports - both in FDM printing and resin printing.

The set includes 22 elements - each of them was printed many times using an FDM printer (Artillery Genius) and a resin printer (Elegoo Mars Pro 2). After each test print, the parts were corrected and refined so that they use as little material as possible, are not time-consuming and have the best possible fit.

Important: For resin printing, I would strongly recommend using flexible magnetic buildplate. Thanks to it, the prints (especially the flat ones) will not be a problem when detaching from the buildplate.

 

You can connect individual wall segments with each other using 3mm x 1mm magnets or simply using glue / blu tack. The connecting pieces also have holes of 2.2mm in diameter, so you can use  2.2mm wires/strands for connecting these pieces.

The largest elements from this set have dimensions of 126.7mm x 15.53mm x 79.95mm - so they will be suitable even for small popular printers (diagonally) - in the case of slightly larger printers such as the Mars Pro 2 on which I tested these models, you will even be able to print 4 main walls simultaneously.

If you have both types of printers, there is nothing to prevent you from connecting the elements printed with filament and resin, then you decide what quality you expect from a given element of the set.

 

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

 

Patreon Rewards – April 2021

In the April pack you will find a new version of my very first model dedicated to 3D printing - The Vined Throne. The new version is much more complex and rich in details (it is best to print it using low layer heights), I spent a lot of time to make sure that it can be printed without any supports. This model is a reference to my other models such as the Goddess of Life etc.

I hope that this model will not offend anyone - I wanted to refer to classic sculptures and paintings showing beauty (in this case - quite intimidating and disturbind beauty) - without a doubt I do not treat it as a study of oversexualized pin-ups, which I do not like.

I am also attaching a few bigger vines to the throne that will look good in his company.

The second part of this set is The Place of Knowledge. It consists of a huge statue of the mysterious Lore Seeker - his hand has a flat platform on which any human-like miniature can fit. The head is available in three versions - full/complete, hollow inside with a hole (the walls are about 4mm thick) and ruined, which can serve as a temporary shelter from enemy arrows or bad atospheric conditions.

The last element of these Rewards are Ritual Circles in two variants. One is "classic", the other one refers to the throne and larger vines, so they can be used in a set.

I hope you will like these models.

Models included in this set:

  • 2 variants of Ritual Circle
  • Small Jungle Tendrils
  • Throne of Vines (2021 version)
  • The Place of Knowledge set (3 pieces)

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • 2 variants of Ritual Circle
  • Small Jungle Tendrils set
  • Throne of Vines (2021 version)
  • The Place of Knowledge set

Patreon Rewards – March 2021

For this month I would like to present you The Bone Stronghold plus a small bonus - the Bone Monolith and Bone Pillar models.
Thanks to this bundle you can create an impressive Stronghold mean for any death-related army/nation/ruler. It's heavily inspired by Ossiarch Bonereapers faction by Games Workshop.

Models included in this set:

  • 4 variants of walls
  • wall corners
  • gate + "skull gate topper", printed separately
  • 2 variants of wall floors
  • stairs
  • The Bone Monolith
  • The Bone Pillar

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Bone Monolith + Pillar
  • Bone Stronghold

Patreon Rewards – February 2021

In this set you will find quite unique, inspired by Indonesian architecture pieces of scenery.

Working on them was a great pleasure, so I would love to expand this set at some point in the future.

Models included in this set:

  • The main temple
  • Three Ritual Platforms
  • Ancient gate
  • Ancient lookout
  • Walls
  • Two reptile statues
  • Shrine
  • Two separate columns

I hope you will like this set, it's a bit... different, so I reallyhope you will find it interesting.
It should be useful for RPG scenery and also wargames (especially for jungle themed gaming boards).

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Baronghan Shrine - Temple Complex

Patreon Rewards – January 2021

Welcome to the Sunken City!
This adventure will lead us to the corners of the underwater ruins of an ancient city - or on the contrary - perhaps it is a city that has been hidden under the water for hundreds of years, and only recently appeared on the surface ...? It will be up to you.

This set includes many barnacles covered objects, as well as elements that you can use to spice up the storyline of your adventure or to diversify your battlefield.

There are many ruins, architectural elements, a throne room, strange-looking geometric structures, and even a giant crab patiently waiting for its victims await in this bundle.

Models included in this set:

  • Sunken City Columns (2 versions)
  • Sunken City Huge Crab
  • Sunken City Ruins #1 - #5
  • Sunken City Throne
  • Sunken City Wall
  • Sunken Scatter Island 1# - #3

and also - Embowed Set:

  • 4 Arcs with optional connectors. These structures are printable in 2-3 pieces.
  • Embowed Scatter Ruins (5 versions)

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

List of files:

  • Sunken City Set

Patreon Rewards – December 2020

I am pleased to present you the December Rewards - The Floating Islands Set.
When designing this set, I wanted it to be an interesting product also for people who are not interested in using actual flying islands. Thanks to this, you will find a variety of scatter scenery that I used to create the islands - all elements such as obelisks and crystals can be printed separately and used in any way not related to flying islands.

There are nine islands - they are divided into small and large. They all stand on rods that can be printed or purchased (for example, on Amazon. Unfortunately, acrylic clear rods don't come really cheap). Large islands use 1 inch rods, small islands use 0.5 inch rods. The minimum height of the rods that can be used for this design is 15cm.

In the files you will find printable rods with a height of 15cm, 20cm and 25cm

All the islands are printed in two parts and can optionally use magnets. The maximum size of the magnets that can be used for the islands is 15mm (diameter) x 3mm (height). If you are using lower magnets, I suggest you use some kind of putty or thick glue to fill the slot.

The upper parts of the islands have been designed to be an interesting element of the scenery even when lying flat on the table. In this way you can get interesting hills with columns or crystal formations, for example.
The set also includes separate lower parts of the islands without any holes - they can be used as hills and rock formations.

Two variants of bases for the islands are also included. Thanks to them, the islands should stand firmly on the table. I suggest using a slightly larger infill for them to make them heavy enough, or weight them down in some other way.

Models from this set do not require any supports (if you are using an FDM printer).

NOTE: This product does not contain any physical models - Contains only digital products in the form of STL files for printing on your own 3D printer.

The miniatures presented in the pictures (dwarf, female druid and warrior) are made by Duncan "Shadow" Louca and are shown only for the scale. They are used with the knowledge and consent of the author. They are not included in the presented product.

 

List of files:

  • Floating Islands Set